รบกวนขอ Error โค้ตอิเล็คทรอลักด้วยครับ

[ถวิล (สกลนคร)]

รบกวนอาจารย์และท่านสมาชิกทุกท่านขอ Error โค้ตเครื่องซักผ้าอิเล็คทรอลักด้วยครับ  โปรดเมตตาผมด้วยครับ

[อ.สำราญ ชนะบุตร]

รบกวนอาจารย์และท่านสมาชิกทุกท่านขอ Error โค้ตเครื่องซักผ้าอิเล็คทรอลักด้วยครับ  โปรดเมตตาผมด้วยครับ

ตอบ ขึ้นอะไรก็ไม่บอก  เอาแบบนี้ไปก่อน

เครื่องซักผ้าไม่ทำงาน มี Error ขึ้น
แบบนี้ยังดีครับ เพราะว่าเครื่องซักผ้ายังอุตสาห์บอกอาการกับเราได้ แสดงว่าอาการยังไม่หนักมาก โดยเครื่องซักผ้าของ Electrolux จะบอกเป็นรหัสประมาณนี้ครับ E10, E20, E40 ไม่ใช่น้ำมันน่ะ ฮ่าๆๆๆๆ มันเป็น Error Code ต่างหากมีความหมายตามนี้เลย

E10 - เกี่ยวกับน้ำเข้าเครื่อง
วิธีแก้ไข

    เปิดก๊อกน้ำ ดูว่ามีน้ำไหลจริงๆน่ะ
    เปิดปั๊มน้ำที่บ้านหรือยัง? (ผมลืมเปิดครับเลยเจอ แหะๆ)
    ดูสายยางน้ำเข้าเครื่องว่า สายยางแบนไหม
    ถ้าคุณติดตั้งตัวกรองน้ำเข้า ให้ทำความสะอาดตัวกรองด้วย


E20 - เกิดปัญหาตอนถ่ายน้ำทิ้ง
วิธีแก้ไข

    ดูท่อระบายน้ำว่างอหรือแบนไหม
    ทำความสะอาดตัวกรองท่อระบายหรือ "Drain Pump Filter" -> อันนี้ผมไม่ได้ล้างครึ่งปีครับ เลยเจอ ฮ่าๆๆๆๆๆๆๆๆ


E40- ฝาหน้าเครื่องเปิดอยู่
วิธีแก้ไข

    เปิด-ปิดใหม่อีกรอบครับ
    ถ้าผ้าเยอะไปก็เอาออกน่ะ อันนี้ผมเลยเป็นตอนที่ยัดผ้าเยอะๆ แล้วปิดไม่ได้ ฮ่าๆๆๆๆ


ถ้า Error Code นอกเหนือจากนี้ให้ดูที่หน้า Error Code จาก Electrolux ตามนี้ครับ

เครื่องซักผ้าไม่ยอมทำงาน ไม่มีเสียง ไม่มีไฟ ไม่มีอะไรเลย
อันนี้ผมก็เคยเจอ T_T น้ำตาจิไหล ทำไมตรูผ่านประสบการณ์อะไรมาบ้างเนี่ย
วิธีตรวจสอบ

    ถอดปลั๊กแล้วคุณไปหาเครื่องใช้ไฟฟ้าอันอื่นมาลองใช้ปลั๊กที่เครื่องซักผ้าคุณเคยใช้ เพื่อดูว่ามันใช้งานได้ไหม
    ถ้าไม่ได้ โชคดีครับแค่ปลั๊กเสีย
   

[อ.สำราญ ชนะบุตร]

แบบ INTER
ELECTROLUX   กับ  ZANUSSI
ระหัส Error  บอร์ดที่ใช้ CPU  EWM2000

E11 - Problems with the bay water when washing

Error occurs when the 10 minutes the water level in the tank does not reach the desired level. Usually this is due to problems with drainage tract. Check valves and hoses, make sure that the water valve to fit cars with good pressure, the grid in the valve is not clogged CM.
The problem can also be caused by a malfunction of the valve supplying water, or damage to the electronic controller CM. You can measure the resistance of the valve winding machines - should be about 3.8 kOhm

E12 - Problems with the Bay water drying

Error appears for 10 minutes during the drying cycle. In this case the check valve repair bay water

E21 - Problems with water drainage

Error occurs when the CM for 10 min does not drain water from the tank. In this case, clean the filter, convinced in the absence of obstruction in the tubes and hoses, and check the work of the discharge pump. Impeller discharge pump rotating left / right to have free course. If not, the pump must be replaced.
The resistance of the coil pump is about 200 ohms. The reason for the defect can also be caused by a malfunction of the electronic controller CM

E22 - Problems with the discharge of water during drying

In this case, clean the condenser drying

E31, E32, EZZ, E34 - Problems caused by a mismatch in the testimony pressostatov

Error occurs:

- If pressostat analog signal that goes beyond the established;
- If not carried out the calibration of the water level;
- Inconsistency in the signals from analog and protective pressostatov;
- If the water level in the tank is too high.

In all cases it is necessary to verify the absence of obstruction in the tubes and the cell selection pressure pressostatov.
It should be noted error «EZZ» - it occurs more frequently than others and are not eliminated by any replacement of the CM. It appears because of the unstable voltage in the network are high. This error may appear when a failure (breakdown in the corpus), the heating element (TENa), as well as irregularities in the chain of power

E41, E42, E43, E44, E45 - something wrong with the lock hatch

Errors occur if the door is not closed tightly or if it's not working to lock hatch. You can check the status of contacts node lock hatch, disconnect the plug. Account. 3 and 4 should be closed, while 4 and 5 - open.
Errors can also be caused by the malfunction of an electronic controller

E51 - defective simistor, Managing driven motor

Error appears when the defective simistor on-board electronic controller or the controller itself may be defective

E52 - something wrong with tahogeneratora

Error occurs when tahogenerator does not form a signal of rotation of the drive motor. In practice, most often occurs as follows: from the vibration during extraction jump spring washer, the restraint coil tahogeneratora. It leave the body and the motor hangs on the wires


E53 - malfunction in the electronic engine management controller

Check serviceability of elements associated with the driver motor. If any items were not identified, replace the electronic controller

E54 - defective one of the relay on the electronic controller

Check serviceability relays, as well as supply chain management in an electronic controller

E61 - slow hot water in the tank

Most often this error occurs at low voltage electrical network

E62 - Increased water temperature in the tank CM (significantly higher than the given)

Check thermistor resistance (5,7 ... 6,3 kOhm - at 20C). Satisfied that Tan did not penetrate to the body. Error can also be caused by a malfunction of the electronic controller

E63 - Lack of heat in the drying

Check the chain and the elements responsible for heating and controlling temperature of drying (see above)

E64 - Overheated drying

In this case, you must check are: Tan, security pressostat, thermistor, and an electronic controller

E66 - defective relay TENa

The discrepancy between the level 2 protective pressostata and the inclusion of relay TENa. Also check the circuit to ground TENa and temperature sensor

E71 - defective temperature sensor wash

Error occurs when the value of the resistance temperature sensor deviates from the norm

E72, E73 - defective temperature sensor drying

Error occurs when the value of the resistance temperature sensor deviates from the norm. Also convinced that the Ten, or the sensor is not trapped in the shell

E84, E85 - defective simistor (located on the electronic controller), Managing circulating pump.

Check serviceability simistora

E91 - A communication error between the electronic controller and display

Check the connectors between the boards. Usually this error is caused by oxidation of the connector contacts

E93, E94 - Configuration Error

When the error is necessary to reconfigure the electronic controller

EF1 - obstruction discharge filter

Error appears with long-term discharge of water (a water level in the tank decreases slightly). In such a case, it is necessary to check all the tubes and hoses, and clean the filter

EF2 - Overdosing detergent

Error appears when you receive the excess amount of foam

[อ.สำราญ ชนะบุตร]

ELECTROLUX   กับ  ZANUSSI
ระหัส Error  บอร์ดที่ใช้ CPU  EWM1000

E11 - Gulf waters during the wash cycle (the water level in the tank had not been reached for the time)

The most probable cause of the error - failure of one of the valves of the Gulf waters, or its management schemes (simistora) on the electronic controller. You can check the winding valve - its resistance should be about 3.75 ohms.
Also, this error may be caused by blockages tract Gulf waters and the low water pressure in water supply

E13 - A water leak in the pan CM

E21 - Over 10 minutes the water was not drained from the tank

The most likely causes of errors: failure of the discharge pump, clogged filter, pipe and tube discharge path. If necessary, you can check the winding discharge pump - its resistance should be about 170 ohms. This error may be caused by a malfunction and an electronic controller

E23 - defective manager simistor discharge pump (located on the electronic controller)

Check and, if necessary, replace the specified simistor

E24 - Defect chain management simistora discharge pump (its elements, as simistor, located on the electronic controller)

Check serviceability of the specified circuit

EZZ - Lack of water level of the sensors (sensor TENa protection from the inclusion of the last without water sensor and the first level)

The most likely causes of such errors can be:
- Defective one of the sensors;
- Clog the tube level sensors, and camera selection pressure for these sensors;
- High voltage power network in the CM;
- Breakdown in the corpus TENa

E3 - The water level in the tank above the allowable

In the Gulf water has been achieved so-called level of overflowing (overflow of the switch was open at the time more than 15s)

E36 - faulty level sensor to protect TENa (AB S)

Check the specified gauge

E37 - something wrong with the first water level sensor (L1 S)

Check the specified gauge

E39 - something wrong with the sensor-level overflow (HV1 S)

Check the specified gauge

E41 - The hatch is open or not tightly closed

Tightly close the hatch

E42 - defective lock hatch

Check locking hatch

E43 - defective simistor Manager (located on the electronic controller) lock lock hatch

Check serviceability manager simistora lock lock hatch

E44 - defective sensor, closing the hatch

Check the specified gauge

E45 - defective components supply chain management simistora lock hatch (its elements, as simistor, located on the electronic controller)

Check the elements of supply chain management lock hatch

E51 - Short-circuiting the administrator simistora drive motor (located on the electronic controller)

Check and, if necessary, replace management simistor driven motor

E52 - tahogeneratora signal from the drive motor is not supplied to the electronic controller

The most probable cause of this error is caused by the fact that from the shell tahogeneratora could jump off fixing the washer, so the coil sensor goes out of his seat

E53 - defective components supply chain management simistora drive motor (its elements, as simistor, located on the electronic controller)

Check the controls simistora drive motor

E54 - «Zalipanie» one of the contact groups relays reverse (a total of two) drive motor (switch located on the electronic controller)

Check and, if necessary, replace the relay reverse

E61 - During the hot water temperature for a certain period of time does not reach the specified value

This code is not available to read in normal mode, the CM - he appears only in the diagnostic mode. You can check Ten - its resistance should be about 30 ohms (at room temperature)

E62 - During the hot water temperature reached a value of more than 88 ° C for 5 minutes

Typically, this error may be caused by malfunction of the sensor temperature. The sensor can be verified by measuring its resistance - it should be within 5.7 ... 6.3 kOhm (at 20 ° C).
Tan is also necessary to check (it is possible breakdown in the corpus)

E66 - defective relay TENa

Check and replace if necessary, as a mere relay TENa, and its control circuit

E71 - Resistance temperature sensor went beyond the limits posed

The most probable reason for this error caused by the break or short-circuiting the sensor or its connecting chains. Sometimes breaking down Ten or sensor (possible breakdown of one of these elements in the building)

E82 - Failed choice provisions selector

E83 - Error reading data from the selector (this code is available for reading only in diagnostic mode

E93 - Configuration Error CM

This defect is eliminated by using the correct configuration code

E94 - Configuration Errors CM and cycle (program)

To eliminate such errors need to rewrite nonvolatile memory controller or replace the card

E95 - Failed connection between the processor and a nonvolatile memory based on the electronic controller

Check the chain between the processor and chip ESPPZU. Also need to check the food on a chip nonvolatile memory

E96 - Mismatched configuration electronic controller and external elements that are connected to it (or not)

Check the line configuration of the electronic controller and the external elements

E97 - Inconsistency in the selector of programs and software of electronic controller

EB1 - The frequency of the supply does not correspond to a valid set

Check parameters of voltage

EB2 - Supply voltage above the allowable limit

Check parameters of voltage

EBZ - Supply voltage below the allowable limit

Check parameters of voltage

[อ.อุทิศ วรรณคร (บ้านช่าง)]

   EWM39012 Electroluk